Skip to content

Install

Note

Go to Kit Assembly to find out how to put together your Helios4 NAS

What you need before you start.

1. microSD Card
You need a microSD Card UHS-I with a minimum of 8GB. We recommend the following models:

  • SanDisk Extreme microSDHC UHS-I Card (32GB)
  • SanDisk Extreme PRO microSDHC UHS-I Card (32GB)
  • Strontium Nitro MicroSD Card (16GB)
  • Samsung microSDHC UHS-I Card EVO Plus (32GB)

Recommended SDcard

You might refer to the SD Card page to find a compatibility list of SD Card models.

2. Micro-USB to USB cable
USB cable

3. Ethernet cable (cat5/6)
Network cable

Step 1 - Download an Helios4 image build

You will need first to download a image build to write on the microSD Card.

Go to Dowload and chose one of the latest build.

Note

Images with .7z extension must be first uncompressed with 7-Zip on Windows, Keka on OS X and 7z on Linux (apt-get install p7zip-full).

Step 2 - Writing an image to a microSD Card

You will need to use an image writing tool to install on your microSD Card the image build you have downloaded.

Under Windows, Mac OS or Linux (via Graphic Interface)

Etcher is a graphical SD card writing tool that works on Mac OS, Linux and Windows, and is the easiest option for most users. Etcher also supports writing images directly from XZ files, without any prerequired decompression. To write your image with Etcher:

  • Download Etcher and install it on your computer.
  • Insert the microSD Card inside your SD card reader (microSD to SD adapter might be needed).
  • Open Etcher and select from your local storage the Helios4 file you wish to write to the microSD Card.
  • Select the microSD Card you wish to write your image to.
  • Review your selections and click 'Flash!' to begin writing data to the microSD Card.

Etcher

Under Linux (via Terminal)

7z e Armbian_5.90_Helios4_Debian_buster_next_4.19.59.7z

sudo dd bs=4M if=Armbian_5.90_Helios4_Debian_buster_next_4.19.59.img of=/dev/sdX conv=fsync

Replace the filename by the image file name you downloaded.

Note

/dev/sdX is where the microSD is mapped in your Linux machine, change the 'X' to your corresponding mapped device. If you set /dev/sdX to a wrong device then you might risk erasing a hard drive or different device than the designated microSD.

Step 3 - Power-up Helios4

Before powering-up insure :

  1. You inserted the microSD Card that you prepared in the previous step.

  2. You connected your computer to the serial port with the Micro-USB to USB cable.

  3. You connected Helios4 to your home network with the Ethernet cable.

  4. You plugged-in properly the DC power connector before powering-up the AC adapter.

Connections

Now you can plug-in / power-up the AC adapter.

Warning

Always proceed with caution when manipulating 110/220V appliance.

Step 4 - Connect to Helios4 serial console

Important

For Windows and Mac OS you will need to install the FTDI driver in order to access the USB to serial bridge used by Helios4. You can find the driver here.

Under Windows

  1. Download PuTTY and install it on your computer.

  2. Select connection type serial.
    Putty connect

  3. Setup serial port settings (Serial line : COM1 and Speed : 115200), then press 'Open'
    Putty config

Note

If you computer already has a serial port then COM1 might not be the correct serial line to connect to Helios4. Check this link to learn how to determine the right COM port.

Under Linux and Mac OS (via Terminal)

  1. Install picocom (under Debian/Ubuntu)

    $ sudo apt-get install picocom

  2. Connect to serial with picocom

    $ sudo picocom -b 115200 /dev/ttyUSB0

Picocom

To exit picocom do Ctrl-a then Ctrl-x

Note

Using command ls -la /dev/tty you should be able the find the USB to serial bridge device used by Helios4. Under Linux the device will be named /dev/ttyUSBx, where x is a digit. Under Mac OS the device will be named /dev/tty.usbserial-xxxxxxxx, where xxxxxxxx is some serial number.

Step 5 - Log in

Note

You might need to press Enter for the login prompt to come up.

Default credential for Debian image

helios4 login: root
Password: 1234

You will be prompted to change the root password and then create a new user account.

First Login

Step 6 - Check/Set IP address

Check IP address

By default Helios4 will try to obtain an IP address via DHCP. To figure out what is the allocated IP address you will need to type the following command in the console.

ip addr show dev eth0

Network Config

Here the IP address of Helios4 is 10.10.10.1.

Set IP address

If you wish to manually configure your IP address you can use the armbian-config tool.

armbian-config

Armbian-config

Armbian-config

Armbian-config

Armbian-config

Press ESC till you exit armbian-config tool.

You will have to reboot for the network settings to take effect.

sudo reboot

Info

You can also refer to the following Debian Wiki Page for advanced network settings.

Step 7 - Connect to Helios4 via SSH

You can now connect by SSH to your Helios4 to carry on with your configuration.

SSH Login

Putty SSH

What to do next ?

If you want to install OpenMediaVault, the next-gen network attached storage (NAS) software, refer to the OMV page.

If you have assembled an OLED Display as part of your Helios4 setup, it can be the right time to set it up. Refer to the following section that will explain you how to install the sys-oled application which control the OLED display.

For other software you can use armbian-config which provides an easy way to install 3rd party applications. You can also refer to our Software section to find tutorials that will help you to setup manually your Helios4.

sudo armbian-config

!armbian-config Main Menu

!armbian-config Software

!armbian-config Selection

Updated on 2019-07-16